Skip to content
Home: Success TutoringTeachers

Grade 4 Science lesson plan · More Science resources

Electric Circuits: Series and Parallel Circuits, Circuit Symbols, Conductors and Insulators

Using battery-powered kits only, students build a simple circuit with a battery, bulb and switch, test everyday materials as conductors or insulators, and compare series and parallel circuits by removing a bulb from each. They draw every circuit with standard symbols and explain why a complete loop is needed.

  • 60 minutes
  • Grade 4
  • Science
  • Electric circuits
  • 🇺🇸 United States

By the Success Tutoring Teachers team · Updated · Educator review in progress · How we make our resources

Download PDF

Overview

Learning objectives

Students will…

  • Build a complete circuit with a battery, bulb and switch, and explain why the bulb lights only when the loop is unbroken.
  • Test materials and classify them as electrical conductors or insulators.
  • Build series and parallel circuits with two bulbs and compare their brightness and what happens when one bulb is removed.
  • Draw circuit diagrams using standard symbols.

Success criteria

Students can say…

  • I can build a circuit with a switch that turns a bulb on and off.
  • I can sort materials into conductors and insulators using test results.
  • I can explain why both bulbs go out in a series circuit when one is removed, but not in a parallel circuit.
  • I can draw a circuit diagram with the symbols for a cell, battery, bulb, switch and wire.

Curriculum focus: Physical Science — Energy · State standards (Texas TEKS first)

Specific curriculum codes are added once our team has checked them against the official documents. How we align resources

Circuits are taught in Grade 4 or 5 in most US programs. Series and parallel circuits make this a full lesson for either grade; for Grade 4, keep the circuit symbols to bulb, battery, switch and wire.

More Texas teacher resources (TEKS and STAAR)

Key vocabulary

circuit
A complete, unbroken loop that electric current can flow around.
current
The flow of electric charge around a circuit.
cell and battery
A cell (such as one AA) is a single source of electrical energy. A battery is two or more cells joined together, though people often call one cell a battery.
bulb
A component that transfers electrical energy into light (and some heat). Its thin wire filament glows when current flows through it.
switch
A component that opens (breaks) or closes (completes) the circuit.
conductor
A material that lets electric current flow through it easily, such as copper, aluminum, steel and other metals.
insulator
A material that does not let electric current flow through it easily, such as plastic, rubber, wood and glass.
series circuit
A circuit with only one path: all components are in a single loop, one after another.
parallel circuit
A circuit with two or more branches, so current has more than one path.
short circuit
A path with almost nothing in it, such as a bare wire joining the two ends of a battery. It lets a very large current flow, making the wire and battery hot.

In the glossary: conductor, electric circuit, electric current, insulator, parallel circuit, series circuit

Materials & preparation

You will need

  • Per group of three, from a school battery-powered circuit kit: a battery holder with 2 × AA cells (3 V total), two bulbs in holders rated for the kit's battery (LEDs with a built-in resistor can replace them for circuit 1 and the parallel circuit, but two LEDs in series often will not light on 3 V, so use bulbs for the series test), one switch, five or six connecting leads with alligator clips
  • A test tray per group: a steel paperclip, a coin, a strip of aluminum foil, a plastic ruler, a rubber band, a wooden craft stick, a glass marble, a piece of paper, and a pencil sharpened at both ends (to expose the graphite)
  • A battery-powered LED flashlight that can be unscrewed, for the hook
  • A circuit symbols chart (drawn on the board or printed)
  • Practice sheet and exit ticket (printable)

Before the lesson

  1. Test every kit before the lesson: put fresh AA cells in each holder and check each bulb lights. Remove any rechargeable lithium cells, damaged batteries or button batteries.
  2. Draw the circuit symbols on the board: cell (a long thin line beside a short thick line; the long line is the positive end), battery (two or more cells side by side), bulb (a circle with a cross inside), switch open (a line with a gap and a hinged line lifted away), switch closed (the hinged line touching across the gap), wire (a straight line, drawn with square corners).
  3. Draw the results tables: Material | Bulb lit? | Conductor or insulator; and Circuit | Brightness | What happens when one bulb is removed?
  4. Check there are no mains-powered devices or power outlets within reach of the work areas.

Safety

  • Use battery-powered kits only (AA cells, 3 V in total). Never use power outlets, plugs, chargers or mains-powered devices in any experiment.
  • Never connect a bare lead directly from one terminal of the battery to the other (a short circuit): the wire and battery can become hot. If anything feels warm, unclip the battery and tell the teacher.
  • Do not use rechargeable lithium cells or button batteries. Button batteries are dangerous if swallowed; keep them out of the classroom kit.
  • Never cut open, crush or try to recharge an ordinary battery. Report leaking or damaged batteries; do not touch any leaked material.
  • Keep water and drinks away from the work area.
  • Handle sharpened pencils carefully and keep alligator clips away from faces.
  • Unclip the battery before changing a circuit and before packing away.

Lesson sequence

  1. 1

    Hook: inside a flashlight

    5 min

    Teacher

    • Switch the LED flashlight on and off. Unscrew it and show the parts. Say: 'Batteries, a light, a switch and some metal strips. Why does the light come on only when I slide the switch? What is the switch actually doing?'
    • Take ideas. Say: 'By the end of today you'll be able to build this yourself, draw it the way electricians do, and wire two lights so that one can go out without the other.'

    Students

    • Suggest what the switch does, in pairs.
  2. 2

    Explicit teaching: complete circuits, symbols, conductors

    12 min

    Teacher

    • Draw a battery, a bulb and two wires as a loop. Say: 'Electric current can only flow if there is a complete loop from one end of the battery, through the bulb and back to the other end. Any gap, and it stops everywhere at once.'
    • Say: 'A switch is just a gap you can control. Closed switch: the loop is complete and the bulb lights. Open switch: there's a gap and the current stops.'
    • Say: 'The battery transfers energy to the circuit. The bulb transfers that electrical energy into light and some heat. The current isn't used up; the energy is.'
    • Point to the symbols chart and name each one. Say: 'Electricians everywhere use these symbols so anyone can read a diagram. Draw wires with a ruler and square corners, and every symbol sits in the loop.'
    • Say: 'Some materials let current flow through them easily: conductors, mostly metals. Others don't: insulators, like plastic and rubber. That's why the metal in a lead is wrapped in plastic.'
    • Check: 'Thumbs up or down: a bulb will light if one wire goes from the battery to the bulb, and the bulb is not connected back to the battery.' (Down: there is no complete loop.)

    Students

    • Copy the symbols chart.
    • Answer the thumbs up or down check.
  3. 3

    Safety briefing

    4 min

    Teacher

    • Read the safety rules aloud (see Safety). Say: 'We only ever use these batteries. Never, ever experiment with power outlets, plugs or anything that plugs into the wall: mains electricity can kill.'
    • Say: 'Never clip a lead straight from one end of the battery to the other with nothing in between. That's a short circuit: the wire and battery get hot very quickly. If anything feels warm, unclip the battery and tell me.'

    Students

    • Repeat the two most important rules back to a partner.
  4. 4

    Investigation: four circuits

    24 min

    Teacher

    • Circuit 1 (5 minutes): 'Build a circuit with the battery, one bulb and the switch. Turn it on and off. Draw it using symbols.'
    • Circuit 2, conductor tester (6 minutes): 'Open the switch. Unclip one lead from the switch and clip a spare lead onto the switch in its place, leaving a gap between the two free clips. Clip each test material across the gap and close the switch. If the bulb lights, the material is a conductor.' Remind groups that the bulb is always in the circuit while testing, so it is never a short circuit.
    • Circuit 3, series (6 minutes): 'Rebuild with two bulbs one after the other in a single loop. Compare their brightness with circuit 1. Then unscrew one bulb. What happens to the other?'
    • Circuit 4, parallel (7 minutes): 'Connect each bulb on its own branch: each bulb has its own two leads going back to the battery. Compare the brightness. Unscrew one bulb. What happens?'
    • Circulate and ask: 'Trace the path of the current with your finger. How many paths are there?' 'Why is the graphite pencil different from the wooden stick?' (Graphite is a non-metal that conducts; the bulb may only glow dimly.)
    • Expected results: conductors are the paperclip, coin, foil and pencil graphite; insulators are the plastic ruler, rubber band, wooden stick, glass marble and paper. Series: both bulbs dimmer than one alone, and both go out when one is removed. Parallel: each bulb about as bright as one alone, and the other stays lit when one is removed.
    • Two minutes before the end: 'Unclip the battery first, then pack the kits.'

    Students

    • Build, test and draw each circuit, recording results in the tables.
    • Unclip the battery before packing away.
  5. 5

    Results and discussion

    8 min

    Teacher

    • Ask: 'In the series circuit, why did both bulbs go out?' (There is only one path. Removing a bulb breaks the loop for everything.)
    • Ask: 'Why did the other bulb stay on in parallel?' (It has its own complete path back to the battery.)
    • Say: 'In series, the two bulbs share the battery's push, so each is dimmer. In parallel, each bulb gets the full push of the battery, so each is about as bright as a single bulb, but the battery runs flat faster.'
    • Ask: 'Are the lights in a house wired in series or parallel? How do you know?' (Parallel: you can switch one light off and the others stay on.)

    Students

    • Explain the results using the words loop, path, series and parallel.
  6. 6

    Exit ticket

    7 min

    Teacher

    • Students complete the exit ticket on their own. Sort it into secure / nearly / not yet.

    Students

    • Answer the exit ticket on their own.

Worked examples

Predicting a series circuit

A battery, a closed switch and two bulbs (A and B) are connected in one loop. Bulb A is unscrewed. Predict and explain what happens to bulb B.

  1. Trace the path: battery → switch → bulb A → bulb B → back to battery. There is only one path, so it is a series circuit.
  2. Unscrewing bulb A makes a gap in that one path.
  3. With a gap anywhere in the loop, current stops everywhere.

Bulb B goes out, because the only path for the current is broken.

Designing a parallel circuit with two switches

Design a circuit with one battery and two bulbs, where each bulb has its own switch.

  1. Each bulb needs its own path back to the battery, so the bulbs must be in parallel branches.
  2. Put one switch in each branch, next to its bulb.
  3. Closing switch 1 completes branch 1 only, so only bulb 1 lights; the same for switch 2.
  4. Draw it: the battery symbol, then two branches side by side, each containing a switch symbol and a bulb symbol, joined back to the battery.

A parallel circuit with a switch in each branch: each switch controls only its own bulb.

Practice & answers

Printable student sheet

Electric Circuits Practice

Use the words loop, path, conductor and insulator in your answers. Draw circuits with a ruler and standard symbols.

  1. 1List what a circuit needs for a bulb to light.
  2. 2Describe the circuit symbols for a cell, a bulb, an open switch and a closed switch.
  3. 3Sort into conductors and insulators: copper wire, plastic ruler, steel paperclip, rubber band, aluminum foil, wooden craft stick, glass marble, coin.
  4. 4Why are the metal wires in electrical leads covered in plastic?
  5. 5Kai builds a circuit with a battery, a bulb and an open switch. Why doesn't the bulb light?
  6. 6Two bulbs are in series. One is unscrewed. What happens to the other, and why?
  7. 7Two bulbs are in parallel. One is unscrewed. What happens to the other, and why?
  8. 8Compare the brightness of two bulbs in series with one bulb on its own, using the same battery.
  9. 9Why are the lights in a house wired in parallel?
  10. 10The graphite in a pencil made the bulb glow dimly. What does this tell you about graphite?
  11. 11Why must you never connect a wire straight from one end of a battery to the other with nothing else in the loop?
  12. 12Some old strings of decorative lights all went out when one bulb failed. Were they wired in series or parallel? Explain.
Show answers
  1. A source of energy (a battery), a bulb, conductors (wires) joining them in a complete loop, and any switch in the loop must be closed.
  2. Cell: a long thin line beside a short thick line. Bulb: a circle with a cross inside. Open switch: a line with a hinged section lifted away, leaving a gap. Closed switch: the hinged section touching across the gap.
  3. Conductors: copper wire, steel paperclip, aluminum foil, coin. Insulators: plastic ruler, rubber band, wooden craft stick, glass marble.
  4. Plastic is an insulator, so it stops current flowing out of the wire into anything (or anyone) touching it, and stops bare wires touching and causing a short circuit.
  5. The open switch leaves a gap, so the loop is not complete and current cannot flow.
  6. It goes out. There is only one path for the current, and removing a bulb breaks it.
  7. It stays lit. It has its own separate path (branch) back to the battery, which is still complete.
  8. Each bulb in series is dimmer than the single bulb, because the two bulbs share the battery's push (voltage).
  9. So each light can be switched on and off on its own, and if one bulb fails the others keep working.
  10. Graphite is a conductor, even though it is not a metal, but it does not conduct as well as the metals tested.
  11. It is a short circuit: a very large current flows, so the wire and battery get hot, the battery drains quickly and it could be damaged or leak.
  12. Series: one failed bulb broke the only path, so current stopped flowing through all of them.

Differentiation

Offer tasks by choice or quietly by invitation — avoid labelling groups by ability in front of the class.

Additional support

  • Give a photo or picture card of each of the four circuits to copy, and a symbols chart with labels.
  • Pair the conductor test with a two-column sorting mat (conductor / insulator) for the actual objects.
  • For circuit diagrams, provide the symbols cut out to arrange before drawing.

Core task

  • Build all four circuits and complete practice questions 1 to 10.

Extension challenge

  • Answer questions 11 and 12.
  • Draw a circuit where one switch controls two bulbs in parallel, and a second switch controls only one of them. (Put switch 1 in the main line next to the battery, before the branches, and switch 2 in one branch.)
  • Predict, then test, what happens to the brightness of one bulb when the battery pack is changed from one cell to two cells. (It is brighter with two cells, because the push, or voltage, is doubled.)

Assessment & exit ticket

Formative assessment

  • Thumbs up or down check on complete circuits.
  • Check each group's circuit drawings for correct symbols and a complete loop.
  • Listen for the explanation of series and parallel results using the idea of paths.
  • Sort exit tickets into secure / nearly / not yet.

Exit ticket

  1. Draw a circuit diagram of a battery, a switch and one bulb using correct symbols.
  2. Name two conductors and two insulators.
  3. You remove one bulb from a circuit and the other bulb stays lit. Is it a series or parallel circuit? Explain.
Show exit ticket answers
  1. A single rectangular loop containing a battery symbol (two cells), a switch symbol and a bulb symbol (a circle with a cross), joined by straight lines.
  2. Example: conductors copper and aluminum foil; insulators plastic and rubber. (Any two metals or graphite; any two of plastic, rubber, wood, glass, paper.)
  3. Parallel. The other bulb has its own complete path to the battery, so it keeps working.

Common misconceptions

  • Current is used up by the bulb. The current is the same all the way round a series loop; it is energy that the bulb transfers into light and heat.
  • Only one wire is needed to light a bulb. The current needs a complete loop: out of one end of the battery and back into the other.
  • Bulbs closer to the battery are brighter. In a series circuit identical bulbs are equally bright, wherever they are in the loop.
  • All metals conduct, so all non-metals insulate. Graphite is a non-metal that conducts.
  • Small batteries mean all electricity is safe. Classroom batteries are low voltage and safe when used properly; mains electricity from power outlets is dangerous and is never used for experiments.

Extension

  • Design and build a battery-powered door alarm or quiz buzzer using a switch made from foil and card (a pressure switch that closes when pressed).
  • Investigate whether the length of a thin wire in the circuit changes the bulb's brightness, keeping everything else the same.

Free resources from other Success Tutoring sites that match this topic.

More lesson plans

Need a timer for this lesson? Open the Classroom Timer or make random groups.