STEM activities
Paper Bridge Strength Challenge
Teams build a bridge from just two sheets of paper to span a 20 cm gap, then load it with coins to find the strongest design. Includes fair-testing rules, a recording sheet and discussion of why folds and shapes add strength.
By the Success Tutoring Teachers team · Updated · Educator review in progress · How we make our resources
Setup
- Collect the coins in bags of 100 so each team gets the same type.
- Set up one demonstration: two book stacks exactly 20 cm apart, with one flat sheet of paper laid across. Put the cup in the middle and add coins until the paper sags to the table. Note the result (usually only a few coins).
- Write the rules on the board: Two sheets of paper. Gap of 20 cm. Bridge rests on the books (no taping to the books). Cup sits in the middle.
Safety
- Keep book stacks low (about 10 cm) and stable so they do not topple.
- Collect and count coins at the end; remind students that coins never go in mouths and to wash hands after handling them.
- Keep the floor clear of dropped coins to prevent slips.
How to run the activity
- 1Show the demonstration bridge collapsing. Ask: 'How could we make the same paper much stronger without adding anything?'
- 2Discuss fair testing: 'What must stay the same for every team so the test is fair?' (gap, paper, coin type, cup position). Record answers on the board.
- 3Teams spend 5 minutes planning and sketching a design on the recording sheet, and predict how many coins it will hold.
- 4Teams build for 12 minutes. Say: 'You may fold, roll, pleat or layer the paper. You may not use extra paper.'
- 5Test bridges one team at a time, or all at once with you calling 'add one coin'. Add coins one at a time to the cup. The bridge fails when the cup touches the table or the bridge falls.
- 6Teams record the last number of coins held before failure.
- 7Teams spend 8 minutes improving their design using a spare pair of sheets, then retest.
- 8Gather results on the board and discuss: 'Which shapes worked best? Why do folds (like a concertina) or tubes make paper stronger?'
Learning outcomes
- Follow a design process: plan, build, test, improve.
- Identify variables that must be controlled in a fair test.
- Explain how shape (folds, tubes, corrugation) affects the strength of a structure.
- Record and compare results accurately.
Printable student sheet
Paper Bridge recording sheet
Plan, build, test and improve your bridge. Record your thinking and results.
- 1Sketch your first design and label the folds or shapes you will use.
- 2Prediction: how many coins will your bridge hold? Why?
- 3List three things that stayed the same for every team to keep the test fair.
- 4Test 1 result: number of coins held before failure.
- 5What did you change for your second design, and why?
- 6Test 2 result, and what you learned about making paper stronger.
Show answers and teacher guidanceHide answers
- Teacher guidance: look for a clear labeled sketch, e.g. a concertina deck resting across the gap or rolled tubes under a flat sheet.
- Any reasoned prediction. Strong answers refer to shape, e.g. 'Folds make it stiffer.'
- Any three of: gap width (20 cm), amount and type of paper, type of coin, cup position, how coins are added (one at a time).
- Record the actual result.
- Teacher guidance: one clear change linked to what failed in Test 1 (e.g. 'It bent in the middle, so we added a second folded layer').
- Record the actual result. Key idea: folding, rolling or layering paper makes it harder to bend, so it carries more load.
Variations
- Shorter session: skip the second build and finish with a discussion of how each team would improve.
- Wider gap: increase the gap to 25 cm and compare results.
- Budget version: tape costs 'points'; teams balance strength against cost.
Extension
- Graph coins held for each design type (flat, folded, tube, layered) and describe the pattern.
- Research and sketch a real bridge type (beam, arch, truss) and explain which paper design it is most like.
Additional support
- Show three starter shapes (concertina fold, rolled tube, folded U-channel) for teams to choose from.
- Give a sentence starter for explanations: 'Our bridge held more because …'
Extension challenge
- Teams must calculate the mass held if each coin's mass is known, and compare strength per gram of paper.
Teacher notes
- Concertina (pleated) decks and rolled tubes usually hold far more than flat sheets: folding stops the paper bending as easily.
- If coins run short, use identical washers or counters; what matters is that every load unit is the same.
Pair it with
Free resources from other Success Tutoring sites that match this topic.
More stem activities
Newspaper Tower Challenge
Teams build the tallest free-standing tower they can from ten sheets of newspaper and one meter of masking tape in 20 minutes. A classic engineering challenge with a printable design log, structured roles and a clear debrief.
One-Sheet Paper Chain Challenge
Small groups have one sheet of paper, a pair of safety scissors and 30 cm of tape to make the longest paper chain they can in 15 minutes. A low-cost group challenge about planning, measuring and teamwork.
Soft Landing: The Cup Drop Challenge
Teams design a landing system that stops a ping-pong ball bouncing out of a paper cup when dropped from shoulder height. Cheap, safe and mess-free, it teaches forces, impact absorption and iterative design.